Prehliadač alebo jeho nastavenia nie sú podporované.

Praktik.ai používa moderné webové technológie kvôli bezpečnosti, rýchlosti a spoľahlivému prihlasovaniu. Tento prehliadač ich nepodporuje alebo blokuje JavaScript, preto sa aplikácia nemusí správne načítať.

Aktualizujte prosím Chrome, Edge, Firefox alebo Safari na najnovšiu verziu a stránku potom obnovte.

Ak používate Windows 7, Windows 8 alebo Windows 8.1, Chrome a Edge už nemusia ponúkať novú verziu. V takom prípade použite novšie zariadenie alebo kontaktujte podporu Praktik.ai.

Prohlížeč nebo jeho nastavení nejsou podporované.

Praktik.ai používá moderní webové technologie kvůli bezpečnosti, rychlosti a spolehlivému přihlašování. Tento prohlížeč je nepodporuje nebo blokuje JavaScript, proto se aplikace nemusí správně načíst.

Aktualizujte prosím Chrome, Edge, Firefox nebo Safari na nejnovější verzi a stránku potom obnovte.

Pokud používáte Windows 7, Windows 8 nebo Windows 8.1, Chrome a Edge už nemusí nabízet novou verzi. V takovém případě použijte novější zařízení nebo kontaktujte podporu Praktik.ai.

Your browser or its settings are not supported.

Praktik.ai uses modern web technologies for security, speed, and reliable sign-in. This browser does not support them, or JavaScript is blocked, so the app may not load correctly.

Please update Chrome, Edge, Firefox, or Safari to the latest version and then reload this page.

If you use Windows 7, Windows 8, or Windows 8.1, Chrome and Edge may no longer offer a newer version. In that case, use a newer device or contact Praktik.ai support.

Not effective Corrigendum to Commission Implementing Decision (EU) 2024/2974 of 29 November 2024 establishing the best available techniques (BAT) conclusions, under Directive 2010/75/EU of the European Parliament and of the Council on industrial emissions, for the smitheries and foundries industry ( Official journal of the European Union L, 2024/2974, 6 December 2024 )

Rozhodnutie č. 2974/2024

Text language

Important dates

Declared: 20. decembra 2024
Approved: 20. decembra 2024

Documents and links

Corrigendum to Commission Implementing Decision (EU) 2024/2974 of 29 November 2024 establishing the best available techniques (BAT) conclusions, under Directive 2010/75/EU of the European Parliament and of the Council on industrial emissions, for the smitheries and foundries industry

On page 44, in Table 1.8, footnotes:

for:

(a)

organic binder systems generating low or no emissions of substances classified as CMR 1A, CMR 1B or CMR 2 (see techniques (d), (e) and/or (f) in BAT 25) are used in core-making;

(b)

one or both of the following conditions are met:

—

thermal or catalytic oxidation is not applicable,

—

substitution with water-based coatings is not applicable.

(1)

The BAT-AEL only applies in the cold-box process when amines are used.

(2)

The BAT-AEL only applies when aromatic binders/chemicals are used.

(3)

The BAT-AEL only applies when the substance concerned is identified as relevant in the waste gas streams based on the inventory of inputs and outputs mentioned in BAT 2.

(4)

The BAT-AEL only applies when phenolic-based binder systems are used.

(5)

In the case of core-making, the upper end of the BAT-AEL range may be higher and up to 100 mg C/Nm3 if both of the following conditions (a) and (b) are met:

read:

(1)

The BAT-AEL only applies in the cold-box process when amines are used.

(2)

The BAT-AEL only applies when aromatic binders/chemicals are used.

(3)

The BAT-AEL only applies when the substance concerned is identified as relevant in the waste gas streams based on the inventory of inputs and outputs mentioned in BAT 2.

(4)

The BAT-AEL only applies when phenolic-based binder systems are used.

(5)

In the case of core-making, the upper end of the BAT-AEL range may be higher and up to 100 mg C/Nm3 if both of the following conditions (a) and (b) are met:

(a)

organic binder systems generating low or no emissions of substances classified as CMR 1A, CMR 1B or CMR 2 (see techniques (d), (e) and/or (f) in BAT 25) are used in core-making;

(b)

one or both of the following conditions are met:

—

thermal or catalytic oxidation is not applicable,

—

substitution with water-based coatings is not applicable.