Not effective Corrigendum to Commission Delegated Regulation (EU) 2015/2420 of 12 October 2015 amending Council Regulation (EC) No 428/2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual use items ( Official Journal of the European Union L 340 of 24 December 2015 )
Vyhláška č. 2420/2015
Important dates
Documents and links
Corrigendum to Commission Delegated Regulation (EU) 2015/2420 of 12 October 2015 amending Council Regulation (EC) No 428/2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual use items
On page 58, item 1C007:
for:
‘Ceramic powders, non-”composite” ceramic materials, ceramic-”matrix”, ”composite” materials and precursor materials, as follows:’,
read:
‘Ceramic powders, non-”composite” ceramic materials, ceramic-”matrix” ”composite” materials and precursor materials, as follows:’;
on page 88, item 1C450.b.5:
for:
‘N-Dialkyl [methyl, ethyl or propyl (normal or iso)] aminoethane-2-ols and corresponding protonated salts, other than N,N-Diisopropyl-(beta)-aminoethanol (96-80-0) and N,N-Diethylaminoethanol (100-37-8) which are specified in 1C350;’,
read:
‘N,N-Dialkyl [methyl, ethyl or propyl (normal or iso)] aminoethane-2-ols and corresponding protonated salts, other than N,N-Diisopropyl-(beta)-aminoethanol (96-80-0) and N,N-Diethylaminoethanol (100-37-8) which are specified in 1C350;’;
on page 105, item 2B201 is replaced as follows:
|
‘2B201 |
Machine tools and any combination thereof, other than those specified in 2B001, as follows, for removing or cutting metals, ceramics or ”composites”, which, according to the manufacturer's technical specification, can be equipped with electronic devices for simultaneous ”contouring control” in two or more axes:
Technical Note: Stated ’positioning accuracy’ levels derived under the following procedures from measurements made according to ISO 230/2 (1988) (1) or national equivalents may be used for each machine tool model if provided to, and accepted by, national authorities instead of individual machine tests. Determination of ’Stated’ positioning accuracy:
|
on page 133, item 3A001.a.5.b.2:
for:
‘A resolution of 12 bit or more with an ’adjusted update rate’ of equal to or greater than 1 250 MSPS and having any of the following:’,
read:
‘A resolution of 12 bit or more with an ’adjusted update rate’ of greater than 1 250 MSPS and having any of the following:’;
on page 185, items 6A001 to 6A001.a.1 are replaced as follows:
|
‘6A001 |
Acoustic systems, equipment and components, as follows:
|
on page 193, item 6A002.a.2.a.2.a:
for:
‘ ”Space-qualified” ”focal plane arrays” having more than 2 048 elements per array and having a peak response in the wavelength range exceeding 300 nm but not exceeding 900 nm.’,
read:
‘A microchannel plate with a hole pitch (centre-to-centre spacing) of 12 μm or less; or’;
on page 256, item 9A004 is replaced as follows:
|
‘9A004 |
Space launch vehicles, ”spacecraft”, ”spacecraft buses”, ”spacecraft payloads”, ”spacecraft” on-board systems or equipment, and terrestrial equipment, as follows
|
Poznámky
(1) Manufacturers calculating positioning accuracy in accordance with ISO 230/2 (1997) or (2006) should consult the competent authorities of the Member State in which they are established.
(2) Manufacturers calculating positioning accuracy in accordance with ISO 230/2 (1997) or (2006) should consult the competent authorities of the Member State in which they are established.